Mills |
  |
|
Featured
USED
Equipment
|
Category |
Item ID |
Capacity |
Material |
Description |
|
Mill |
21187 |
|
SS |
Retsch Gmbh 5657, Haan,
West Germany, Type SR3, S/N 71585, Watt 2200, V 3x220-60 Hz, S/S Cutting
Mill, Hopper Fed |
|
Mill |
21189 |
|
SS |
Quadro Comill 197 S, all
Sanitary S/S Construction, V Belt Driven by 1HP Motor on Stand |
|
Mill |
22814 |
|
|
QUADRO MILL GRINDER |
|
Mill |
21076 |
15 |
SS |
Used Oakes Mill System, M/N
4MB15A, XP Stop/Start Unit has 15HP US Varidrive, XP 1,000-8,500 RPM, all
Sanitary with Waukesha Size 15 Pump Set on Rolling Cart, 1" In/Out |
|
Mill/Ball |
22490 |
6 |
Steel |
6 X 5 PATTERSON STEEL BALL
MILL
Details: 6 ft. dia. x 5 ft. long steel ball mill vessel.
Ultrasound testing by SWTI yielded the following: Jacket: .383
inches to .394 inches; Average: .385 inches.
Interior: .463 inches to .553 inches;
Average: .500 inches. |
|
Mill/Ball |
22489 |
8 |
Steel |
8 X 6 PATTERSON STEEL BALL
MILL
Details: Jacketed wet grinder. 150
HP, 550 V, 3 phase, 1780 RPM motor with Westinghouse gear reducer.
Jacket gears and interior are in very good condition.
Unit was mounted on concrete blocks.
Cleaned and painted. Interior
readings: .775 .849 .868 .885 .838 .848 inches.
Side wall readings: 1.63 and 1.559 inches.
|
|
Mill/Ball |
23289 |
9 |
NiHard liners/lifters |
One used Ball mill.
Includes ball mill and drive system less 300 HP motor.
9' Diameter x 60" long (cylinder section) ball mill complete with
installed like new NiHard liners/lifters and installed like new outlet
gratings (with 1/2" slot openings). Multiple spare sets of brand new
NiHard liner plates. Hansen gear reducer (1200 rpm motor reduced down to
260 RPM pinion shaft). Main mill trunion bearing housings and bearing
sleeves. Spur gear pinion shaft and coupling. Main ring gear (wraps around
the mill and meshs with the pinion shaft; reduces the mill speed from 260
RPM to 20 RPM). Two pinion shaft bearings and housings. Inching drive gear
box and motor. Large ring gear shrouds. Unit was used for about a year or
less. Excellent condition, like new. MPSI mill, S/N 18542; MPSI bearing
housings, S/N 25947; Hansen gearbox, type RDF-21F-AND, S/N 8801-9374. |
|
Mill/Colloid |
21296 |
10 |
SS |
Greerco M/N W-500-V,
Horizontal Collid Mill, Sanitary, S/S Construction, Jacketed, Micrometer
Adjusment Driven by 10HP, 3/60/230-460 Volt, 3500 RPM Explosion Proof
Motor, Mounted on Base with Casters |
|
Mill/Comminuting
Machines |
21175 |
|
SS |
Used Fitzpatrick S/S, D6
Special, Nitrogen/Vacuum Capable, 25HP, 3500 RPM Motor on Steel Stand |
|
Mill/Comminuting
Machines |
21185 |
|
SS |
Fitzpatrick Comminutor,
Model D6, S/S Construction, Fitzmill, Pan Feed, Swing Type Hammer Rotor,
Driven by 5HP, 3/60/220-440V, 1750 RPM, TEFC Motor, Mounted on Base with
Casters |
|
Mill/Comminuting
Machines |
21186 |
|
SS |
M/N D-6 Fitzpatrick
Comminutor, S/S Fitzmill, Model D-6, S/S Construction, Pan Feed, Swing
Type Hammer Rotor, Driven by 5HP, 3/60/220-440V, 1750 RPM, Explosion Proof
Motor, Mounted on Base with Casters |
|
Mill/Comminuting
Machines |
22811 |
|
316 |
KEMUTEC
MODEL 220 CONE MILL, 316 & 304 SS, |
|
Mill/Comminuting
Machines |
22812 |
|
|
FITZMILL GRINDER 01 |
|
Mill/Comminuting
Machines |
22813 |
|
|
FITZMILL GRINDER 02 |
|
Mill/Crusher |
21173 |
|
|
Used Pennsylvania Crusher,
Size CF00-16 S/N 180, 10HP Motor, Frame 44-2564-41, Varidrive Motor on
Stand |
|
Mill/De-Lumper |
21167 |
|
|
Unused Franklin Miller,
12" Inline De-Lumper M/N PD, Steel, 10HP, 230/460V Motor and Gear
Reducer |
|
Mill/De-Lumper |
21168 |
|
SS |
Sprout Waldron, S/S De-Lumper/Grinder,
12' long x 5" dia Fish Hook Design on Stand with 5HP Motor |
|
Mill/De-Lumper |
23301 |
10 |
SS |
KEK Model 340 Betagrind
Cone Mill (sames as Quadro Model 196S. The Model 196S features a low noise
level and an output capacity of 5,000 lbs per hour), stainless steel
construction, 340mm dia, "V" belt driven by 10 Hp., 3/60/230-
460 volt, 1730 RPM motor, mounted on fixed base in an epoxy coated
enclosure. |
|
Mill/Disc |
21174 |
|
SS |
Used JH Day Poly Disc Mill,
10" dia x 6" high, S/S Shaft, S/S Bowl, 2 Motor Machine All XP
Enclosures, 1HP 875 RPM, Drive Motor, 1/2HP Secondary Motor |
|
Mill/Grinder |
21170 |
|
CS |
Alpine Model-B20/10ROE
Rotoplex Vertical Cutting Mill Plastics/Rubber Granulator/Grinder, C/S
Construction, Driven by 4 KW, 3/60/460V, 1720 RPM TEFC Motor, Mounted on
Portable Base with Casters, Complete with Hoppper & Start/Stop
Buttons, 1983 (Particle Size Adjustable by Changing Sieve Inserts) |
|
Mill/Grinder |
21178 |
|
SS |
S/S New Jersey Grinder on
S/S Cart, 3HP Motor |
|
Mill/Hammer |
21166 |
|
CS |
Pulva Grinder #A-GF, C/S on
Legs, S/N 3252, 5HP Motor Top Feed with Hopper, New Spare Hammers |
|
Mill/Hammer |
21169 |
|
CS |
Kamas, C/S, Hammer Mill on
Stand with Controls, Motor, approx. 5HP, Swedish |
|
Mill/Hammer |
21172 |
|
|
Bantam, No Body, No Hammers |
|
Mill/Hammer |
21179 |
|
Steel |
Used Pulva P.M.C.O. #3TH,
Steel Hammermill Grinder, 4 Rows of Stirrup Hammers, 3 Screw Feeders,
approx. 25HP Belt Drive Motor, 1HP Feed Motor on Steel Stand, Older
Machine |
|
Mill/Hammer |
21180 |
|
SS |
Used Pulva #B2, S/S Swing
Hammers & Liner, C/S Frame, Cover, As Is |
|
Mill/Hammer |
21181 |
|
CS |
Used Pulva 1, C/S on Stand,
Sampler Mill |
|
Mill/Hammer |
21183 |
|
CS |
1 SH Mikro Pulverizer,
Steel, Mfg. Mikropul, Model 1 SH, Steel Construction, Fractional HP
Horizontal, Screw Feeder, Stirrup Hammers, Drive Motor on Base with Hopper
in a Dust Closure, No Legs |
|
Mill/Hammer |
21184 |
|
CS |
Used 3 SH Mikro Pulverizer,
Carbon Steel Construction, Harded Faced Stirrup Hammers, V-Belt Driven by
approx. 40HP TEFC Motor, Maximum RPM 4600, 2HP Tri-Screw Feed all Mounted
on Steel Frame 39" high from Bottom Discharge, S/N 72J1 |
|
Mill/Hammer |
23335 |
|
CS |
One Used CS Hammer Mill, 15
hp, with win screw feeder driven by 1/4 hp motor, on stand. |
|
Mill/Hammer |
23341 |
|
SS |
One used SS
Mikro-Pulverizer, Type SH, max RPM 9700. |
|
Mill/Hammer |
23343 |
|
SS |
One used Lab Size Mikro
Pulverizer, Type CF. SS |
|
Mill/Hammer |
22481 |
25 |
CS |
3
TH Mikro Pulverizer, C/S
Mikro Model 3TH, Mikro pulverizer, carbon steel construction, stirrup
hammers with hardsurfacing, triple screw feeder, complete with app. 25
Hp.motor, dust relief, on base. |
|
Mill/Hammer |
22491 |
50 |
|
50 HP HENKE HAMMER MILL
Details: 230/460 V, 3 phase, 3540 RPM motor. Built on 8 ft. long frame.
16 inch opening. Includes
blower. Overall ht. 60
inches. #2.
|
|
Mill/Hammer |
22477 |
60 |
CS |
One used Prater Blue Streak
Hammermill, Triple Reduction, swinging hammer type, 4.46 Style, Model DS7.
60 HP, CS, 208/220/440 VAC 3 Ph motor |
|
Mill/Hammer |
22492 |
60 |
|
60 HP HAMMER MILL
Details: Top opening is 10 x 20 inch.
3 phase, 3555 RPM motor. On
table.
|
|
Mill/Hammer |
22499 |
75 |
|
UNUSED BUFFALO HAMMERMILL,
MODEL # W 25 H - 25" WIDE
INTERNAL WITH 24" ROTOR - 160 HAMMERS - MAXIMUM
SPEED IS 2200 RPM'S - CAN TAKE FROM 40 TO 75 HP MOTOR -
CARBON STEEL - NO SUB BASE AND NO MOTOR INCLUDED.
CAN TAKE REGULAR SCREEN OR BAR GRATE - SCREEN IN MILL
HAS 1/4" OPENINGS - HAMMERS ARE 3/16" THICK -
IDEAL MOTOR FOR THIS MILL IS 40 OR 50 HP - 552 SQ INCH OF
SCREEN AREA.
OVERALL: 34" HIGH -
38" FRONT TO BACK - 44" WIDE
|
|
Mill/Hammer |
22480 |
100 |
Steel |
100
Hp Jacobson "Full Circle" Pulverator, Steel
Mfr.: Jacobson, Model P-271DFF, S/N 32601, 3600 rpm hammermill, variable
speed screw feed, Drive motor: 100 Hp 3/60/230-460/3565 rpm TEFC. |
|
Mill/Kady |
21289 |
50 |
SS |
150 Gallon Kady Mill, S/S
Jacketed M/N 2BH (now known as 2C-50), S/S Wetted Parts, 30 Gallon - 125
Gallon Working Capacity per Minute, 50HP, 3/60/220-440 Volt 1800 RPM, TEFC
Motor, S/S Cover on Base with Legs |
|
Mill/Knife |
21176 |
|
SS |
Used S/S Taylor-Stiles, 4
Knife approx. 6" wide S/S Body Rotor and Cover, S/S Screw Feet, S/S
Hopper, .5HP Reeves Varidrive, 15HP, 3/60/200 Motor, Screw Fed, 3500 RPM
on Stand with Rollers, S/S Body, Rotor, Cover, Screen Feed, C/S Blades -
Complete |
|
Mill/Knife |
21177 |
|
SS |
Used S/S Taylor-Stiles, 4
Knife, approx. 6" wide Screw Fed, .5HP Reeves Varidrive, 15HP,
3/60/200 Motor, 3500 RPM on Stand with Rollers - Missing Cover |
|
Mill/Media |
21293 |
5 |
SS |
4 Liter Netszch Horizontal
Media Mill, M/N LME-4-T, S/S Construction, 2-4 Liter Grinding Chambers
each with own 5HP Variable Speed Drive, Jacketed Chamber, Molinex Style
Agitator, Mechanical Seals, Heat Exchanger with Controls, Mounted on Self
Contained Cabinest, Built 1987 |
|
Mill/Other |
21171 |
|
SS |
150 Gallon Kady Mill, S/S
Jacketed Mode-2BH |
|
Mill/Other |
23290 |
27 |
|
Entoleter Mill 27"
dia. rotor (4800 rpm), 75 hp continuous duty motor |
|
Mill/Pellet |
21290 |
40 |
|
Master Model California
Pellet Mill, Mfg. California Pellet Mill, Unit Mounted on Base with Feeder
Conditioner, Unit Direct Driven by 40 HP, 3/60/230-460 Volt, 1185 RPM,
TEFC Motor, S/N 264558 |
|
Mill/Pulverizer |
21298 |
|
SS |
Rietz M/N RI6K211, Inline
Disintegrator, S/S Construction, Unit is for Parts, Shaft, Body, Seal and
Pulley |
|
Mill/Pulverizer |
23340 |
|
SS |
One Used Fitzmill, SS, 7.5
hp |
|
Mill/Raymond |
21164 |
|
|
Used Raymond Imp Mill #3,
Unit has 50HP Drive Motor, Steel Contact PArts, Whizzer Classifier is
66" dia with Reeves Drive and Motor, Raymond Fan #12 with 50HP Motor,
Prior use was Limetstone with 1-6 Ton/Hour Output, Depending on Condition
and Product |
|
Mill/Raymond |
21165 |
|
|
Used Raymond 50"
Journals |
|
Mill/Raymond |
21188 |
|
|
Used Raymond Mill, M/N
6669, 66" Mill, Built in 1963, Complete with 360HP Motor, 4160 V
Drive Motor, Raymond Fan with 250HP Fan Motor, 8' Double Whizzer, Bull
Ring has never Spun, Vertical Shaft has had Bearing Retrofit, Mill was
Working through 1/20/00 Grinding Talc, There are some Spare Parts
Available with this Mill - N.O.I. |
|
Mill/Raymond |
21190 |
|
|
Used Raymond Roller Mill,
#5048, 4 Journals, 75HP 5'8 1/2" Single Whizzer, 75HP Drive and Fan
Motor, "As Is" |
|
Mill/Roll |
21086 |
|
|
Used 2 Roll Mill 4" x
8" Chrome Rolls, Brabender Hot Oil System for Heating Reeves 1 1/2HP
Varidrive with Cabinet on Rolling Cart |
|
Mill/Roll |
21163 |
|
|
Used Williams 30"
Comet Roller Mill, 4 Journals, Bull Ring, Rollers & Wear Parts are in
Good Condition, 40HP Drive Motor, 3/60/220-440, Double Whizzer Inc. Mill
is Ready to Work, S/N 13120, 1957, Prior use was Cocoa |
|
Mill/Roll |
21292 |
|
SS |
Lehmann Three Roll Mill,
5" dia x 11" S/S Watercooled Rolls, Hand Wheel Roll Adjustment,
Complete with Apron, Guides, Drive, Mounted on Stand |
|
Mill/Roller |
21282 |
|
CS |
Sprout Waldron C/S 3 Pair
High, 2 Rolls, 10" x 36" Roller Mill |
|
Mill/Sand |
21182 |
|
SS |
Used Chicago Sand Mill,
Model 3P, S/S Housing, all XP Stop/Starting, XP 7 1/2HP Horsepower Motor,
230-460 |
|
Mill/Sand |
23362 |
|
|
Used Sand Mill |
|
|
